From csus.edu!wupost!howland.reston.ans.net!math.ohio-state.edu!darwin.sura.net!convex!horak Mon May 31 16:06:54 PDT 1993 Article: 24105 of rec.radio.shortwave Newsgroups: rec.radio.shortwave Path: netcom.com!csus.edu!wupost!howland.reston.ans.net!math.ohio-state.edu!darwin.sura.net!convex!horak From: horak@convex.com (David Horak) Subject: Pro2005/6 SSB MOD HERE! Message-ID: Sender: usenet@convex.com (news access account) Nntp-Posting-Host: eugene.convex.com Organization: CONVEX Computer Corporation, Richardson, Tx., USA Date: Mon, 31 May 1993 18:07:23 GMT X-Disclaimer: This message was written by a user at CONVEX Computer Corp. The opinions expressed are those of the user and not necessarily those of CONVEX. Lines: 58 For those who want to receive 30 MHz and above SSB on your shortwave, here is a mod for the Pro2005/6 that enables you to interface it to your shortwave....... This is the mod for adding SSB capability to your Pro2005/2006. It is taken in part from Bill Cheek's Scanner Mod Handbook Volume 1. As long as you have a shortwave receiver with an external antenna jack and capability to tune to 455 KHz, you can interface it to the Pro2006 with this mod. It is best if you use a static safe work environment to perform this mod and you should have some technical knowledge. Also, a schematic would be helpful but is not necessary. You will need the following parts: Output jack (I use a 1/8 mini earphone jack but some like a BNC. The 1/8 mono jack is easier to install because you don't have to drill as big a hole in the back of the unit) .01 uF capacitor 5 Kohm resistor (1/4 watt) 6 inches of mini coax or other shielded cable A cable to run from the 2006 to your shortwave. I use the shielded cable that has the 1/8 plug on one end and a phono plug on the other end (1992 catalog Radio Shack P/N 42-2444 works for me). The phono plug is perfect for the antenna input of my DX440 shortwave receiver. The first step is to remove the cover of the unit and drill a hole in the back of the 2006 for your 1/8 or BNC plug. (You will want to wrap some tape around the drill bit about an inch from the end to keep it from cruising right on into the electronics once it punches through the metal!) Solder the 5K resister to one end of the .01 uF cap. Solder the other end of the cap to the shielded coax wire. Solder the other end of the coax to your 1/8 phono plug (or BNC) and ground the cable at this end. Now that the cable is in place you are ready to connect it to the 455 KHz source which is D33. It is on the top circuit board near the middle left, not too far from a huge capacitor. Solder the end of the resistor to the cathode of D33. (This should be the top of the standup part) Now you can test it out before you put the cover back on to make sure you did everything correct. You should be able to tune to some local airport or CB frequency on your 2006 and receive the same thing on your shortwave (with it tuned to 455 KHz and hooked up to the 2006 of course). If you tune something on your scanner that is SSB, you should be able to switch your shortwave to SSB and tune in the signal just fine. Beware of one thing, since the 2005/6 only tunes in 5 KHz increments minimum, you may notice from time to time that the signal on your shortwave isn't real clear. It may be that you will need to tune the shortwave anywhere from 451 to 459 KHz to tune in the signal well! If you don't succeed or this description has you baffled you probably shouldn't be doing the mod in the first place. I assume no responsibility for screwups. Good luck David